Controllers & Alarms

Products > Instrumentation > Controllers & Alarms

Bulkhead

High Resolution Weighing Indicator and Controller (SMW-HR)
  • Resolution of 500,000 counts
  • Multi-point linearisation capability (4 points)
  • 12 Calibration profiles stores for 12 different sensors
  • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
  • Six wire measurement system can compensate for zener barrier losses
  • Fully digital set-up and calibration using built-in LCD display and keypad or comms
  • Auto tare and peak hold actioned by volt-free contacts
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • IP65 / NEMA4 ABS housing for bulkhead mounting
  • AC or DC power supply options
Details
Load Cell Amplifier and Digitiser Module (LCA20)
  • Full digital set–up using PC or keypad
  • 3 x configurable digital inputs e.g. for autotare, peak hold and reset
  • RS485 and RS232 digital data output for communications and printing
  • Measurement speeds 10 / 80 samples per sec
  • Factory calibration in mV/V
  • 5 V excitation supports up to 10 x 350 R load cells
  • Fully isolated 4-20 mA and 0-10 V analogue outputs
  • 6 wire input to compensate for barrier and cable losses
  • 2 set points SPCO relay outputs
  • Sensitivity from 0.5 to 7.8 mV/V
  • 10 pt linearization
  • Firmware now supports Mantrabus 1 & 2, MANTRA ASCII 2 & MODBUS RTU
  • ROHS Compliant & Environmentally sealed to IP65 / NEMA 4 enclosure dimensions 200 x 120 x 75 mm
  • Supplied in IP65 NEMA4 ABS protected case, stainless steel version or Din rail option see LCB
  • The LCA20 shown in main photo has the transparent lid option (LTL)
Details
Load Cell Junction Box and Fault Monitoring Alarm (LCI)
  • For the protection of multi-load cell installations such as silos, tanks
  • Alarm will be activated if:
  • One or more load cells are out of balance
  • Any load cell is operated outside a preset mV/V range
  • Excitation voltage deviates from preset range
  • Any connection is lost (open circuit detection)
  • Any short circuit is detected
Details
Universal Digital Signal Conditioner and Controller (UAB)
  • Wide range of Plug-In input modules providing transducer excitation
  • Fully flexible – any input module can be combined with any output module
  • Fully digital set-up and calibration using hand held plug-in display/keypad or comms
  • Optional local or remote LCD display and keypad
  • Simple one pass digital calibration for minimum set-up time on site
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • High accuracy and high stability over a wide temperature range
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • PCB (UAB) options include with case (D3) or without case (D2), DIN rail mounted
Details
Versatile Indicator and Controller (SMP)
  • Large LCD display and keypad
  • Wide range of plug in input modules that provide transducer excitation
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • PID control capability, peak hold, measurement in any engineering units
  • Fully digital set-up and calibration using built-in LCD display and keypad or comms
  • High accuracy and high stability over a wide temperature range
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • IP65 / NEMA4 ABS bulkhead mounting enclosure
  • AC or DC power supply options
Details
Weighing Indicator and Controller Bulkhead Mounted (SMW)
  • Large high resolution LCD display
  • 10V 160mA excitation for up to 6 Load Cells
  • Simple one pass auto calibration
  • 2 Set points, SPCO relay outputs
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications
  • IP65 / NEMA4 ABS housing for wall or surface mounting  
  • Details

    DIN Rail, Rack & PCB Modules

    Load Cell Amplifier and Digitiser PCB (LCB20)
    Load Cell Amplifier and Digitiser PCB (LCB20)
    • PCB version
    • Simple auto calibration
    • 5V Excitation supporting up to 10 x Load Cells (350 R)
    • 0.5 to to 7.8 mV/V sensitivity
    • 6 wire input to compensate for barrier and cable losses
    • Full digital set-up and calibration using keypad or PC
    • Fully isolated analogue outputs 4-20mA & 0-10V
    • 10 pt linearization
    • Three x configurable digital inputs
    • Relay outputs:2 Setpoints SPCO
    • RS485 RS232 digital data output for communications and printing
    • Supports MODBUS RTU, ASCII & MANTRABUS
    • PCB (LCB20 shown in main photo) options include various cases with or without DIN rail mounting (shown in photos on left)
    • The LCB20 also has the option of a stainless steel case
    Details
    Load Cell Junction Box and Fault Monitoring Alarm (LCI)
    • For the protection of multi-load cell installations such as silos, tanks
    • Alarm will be activated if:
    • One or more load cells are out of balance
    • Any load cell is operated outside a preset mV/V range
    • Excitation voltage deviates from preset range
    • Any connection is lost (open circuit detection)
    • Any short circuit is detected
    Details
    Universal Digital Signal Conditioner and Controller (UAB)
    • Wide range of Plug-In input modules providing transducer excitation
    • Fully flexible – any input module can be combined with any output module
    • Fully digital set-up and calibration using hand held plug-in display/keypad or comms
    • Optional local or remote LCD display and keypad
    • Simple one pass digital calibration for minimum set-up time on site
    • Fully isolated 4-20mA and 0-10V analog outputs
    • Setpoints and event handling using digital inputs and 2 x SPCO relays
    • High accuracy and high stability over a wide temperature range
    • RS232 or RS485 communications for setup, data transfer or label/ticket printing
    • PCB (UAB) options include with case (D3) or without case (D2), DIN rail mounted
    Details

    Panel Mount

    Batch Weighing Controller, 12 Ingredients or Components (ADW-BW)
    • Up to 12 components or ingredients
    • Optional 10 menu selection
    • Selectable batch totals
    • Mixer timing control
    • Stand alone or PLC operation
    • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
    • Variable gain input sensitivity from 0.5 to 200 mV/V
    • 6 wire input to compensate for zener barrier and cable losses
    • Simple one pass auto calibration for minimum set-up time on site
    Details
    Panel Mount Weighing Indicator and Controller (ADW15)
    • Direct Strain Gauge input 4.5 digit resolution
    • Variable sensitivity from 0.5 to 200mV/V
    • Excitation 10V 160mA to drive up to 4 load cells
    • 6 wire input to compensate for zener barrier and cable losses
    • Simple one pass auto calibration for minimum set-up time on site
    • Auto tare and peak hold actioned by volt-free contacts
    • Fully isolated 4-20mA and 0-10V analog outputs
    • RS232 or RS485 communications for setup, data transfer or label/ticket printing
    • Programmable in-flight compensation for dynamic weighing operations
    • AC or DC power supply options
    Details
    Versatile Indicator, Controller, Analogue Conditioner (ADP15)
    • Large LCD display and keypad
    • Wide choice of input modules with transducer excitation
    • Fully isolated 4-20mA and 0-10V analog outputs
    • 2 Setpoints with relays outputs
    • Latching and inversion of relays
    • PID control, peak hold, display in engineering units
    • Fully digital set-up and calibration using keypad or comms
    • High accuracy and high stability
    • RS232 or RS485 data for setup, data transfer or label/ticket printing
    • Small panel space – DIN 72 x 72 mm – DIN rail mounting kit available
    • AC or DC power supply options
    Details
    Versatile Indicator/Controller with up to 16 Set Points (ADP-SP16)
  • Up to 16 set point relays (Rating 230V @ 5A AC)
  • All settings programmable from ADP15 keypad
  • Individual programmable setpoints & hysteresis values
  • Wide choice of input modules with transducer excitation
  • Industry Standard Analogue Outputs
  • Data Communications, Printer Driver
  • AC or DC power supply options
  • Details
    Weighing Indicator Controller with up to 16 Set Points (ADW-SP16)
    • Up to 16 setpoints, each with an associated SPCO relay (on DIN rail module)
    • Individual set point, In-flight & hysterisis values
    • Programmable from the ADW keypad
    • Relay contact rating 230V @ 5A AC
    • Communications and Printer Driver
    • Simple one pass auto calibration for minimum set-up time on site
    • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
    • Variable gain input sensitivity from 0.5 to 200 mV/V
    • 6 wire input to compensate for zener barrier and cable losses
    • RS232 or RS485 communications for setup, data transfer or label/ticket printing
    Details
    Weighing Indicator/Controller for Fast Fill Operations (ADW-FFW)
  • For fast & accurate fill control
  • Fast 100 updates per second input
  • Fast & slow feeds
  • System speed optimisation
  • Auto tare
  • Auto calibration
  • Auto ‘In Flight ‘ compensation
  • ‘Weight complete’ output
  • Stand alone or control with PLC
  • Details

    Copyright © 2018 Sensors AS - All Rights Reserved
    |HOME| |PRODUCTS| |HYDROPOWER| |NEWS| |CONTACT|
    ---
    Sensors AS | Lørdagsrudv. 2 | 1472 Fjellhamar | Norway | Phone: +47 67 90 43 00 | Org. nr. NO 982 517 346 MVA

    Sensors AS