Data Output Signal Converters

Products > Instrumentation > Data Output Signal Converters

Bulkhead

Enclosure for 1 x DSC (Strain Gauge or Load Cell Digitiser Module) (DSJ1)
  • Enclosure features
  • Bus connections for communication and power supply
  • 2 part connectors for field terminals
  • D type 9 pin connecter for easy RS232 connection
  • Green LED power indicator
  • Red LED digital output indicator
  • Push switch to simulate digital input
  • CAN compliant – option
  • Does not include the case (as shown in the photo) or the DSC
Details
Enclosure for 4 x DSC (Strain Gauge or Load Cell Digitiser Module) (DSJ4)
  • Enclosure for 4 x DSC Digital load cell conditioning cards
  • Waterproof IP65 NEMA4 bulkhead mounting
  • Bus connections for communication and power supply
  • 2 part connectors for field terminals
  • 9 pin D type for easy RS232 connection
  • LED power and output indicators
  • Push switch to simulate digital input
  • CAN compliant – option
  • Does not include the case or the 4 x DSCs (as shown in the photo)
Details
High Resolution Weighing Indicator and Controller (SMW-HR)
  • Resolution of 500,000 counts
  • Multi-point linearisation capability (4 points)
  • 12 Calibration profiles stores for 12 different sensors
  • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
  • Six wire measurement system can compensate for zener barrier losses
  • Fully digital set-up and calibration using built-in LCD display and keypad or comms
  • Auto tare and peak hold actioned by volt-free contacts
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • IP65 / NEMA4 ABS housing for bulkhead mounting
  • AC or DC power supply options
Details
Load Cell Amplifier and Digitiser Module (LCA20)
  • Full digital set–up using PC or keypad
  • 3 x configurable digital inputs e.g. for autotare, peak hold and reset
  • RS485 and RS232 digital data output for communications and printing
  • Measurement speeds 10 / 80 samples per sec
  • Factory calibration in mV/V
  • 5 V excitation supports up to 10 x 350 R load cells
  • Fully isolated 4-20 mA and 0-10 V analogue outputs
  • 6 wire input to compensate for barrier and cable losses
  • 2 set points SPCO relay outputs
  • Sensitivity from 0.5 to 7.8 mV/V
  • 10 pt linearization
  • Firmware now supports Mantrabus 1 & 2, MANTRA ASCII 2 & MODBUS RTU
  • ROHS Compliant & Environmentally sealed to IP65 / NEMA 4 enclosure dimensions 200 x 120 x 75 mm
  • Supplied in IP65 NEMA4 ABS protected case, stainless steel version or Din rail option see LCB
  • The LCA20 shown in main photo has the transparent lid option (LTL)
Details
Serial ASCII Display Module (SERIALDIS)
  • 6 digit 7 segment LED 20mm display
  • Summation of 6 sensors
  • RS232 or RS485 serial ASCII input
  • Supports multidrop on RS485 (up to 15 sensors)
  • Waterproofed to IP65 NEMA 4
Details
Versatile Indicator and Controller (SMP)
  • Large LCD display and keypad
  • Wide range of plug in input modules that provide transducer excitation
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • PID control capability, peak hold, measurement in any engineering units
  • Fully digital set-up and calibration using built-in LCD display and keypad or comms
  • High accuracy and high stability over a wide temperature range
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • IP65 / NEMA4 ABS bulkhead mounting enclosure
  • AC or DC power supply options
Details
Weighing Indicator and Controller Bulkhead Mounted (SMW)
  • Large high resolution LCD display
  • 10V 160mA excitation for up to 6 Load Cells
  • Simple one pass auto calibration
  • 2 Set points, SPCO relay outputs
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications
  • IP65 / NEMA4 ABS housing for wall or surface mounting  
Details

DIN Rail, Rack & Other

Portable Strain Gauge or Load Cell Indicator (PSD)
  • Portable handheld digital load cell indicator weighing only 250grams
  • Waterproof IP65 NEMA4 battery powered
  • 7 digit LCD display, with battery, peak, trough, net, overload and shunt cal indication
  • Battery life of 450 hrs in power save mode
  • Tactile keyboard, with on/off, range select, peak/valley hold, and gross/net controls
  • Microprocessor based, allowing single pass calibration facility (direct mV/V)
  • Dual range for values such as Kg and lb
  • TEDS enabled for automatic sensor calibration (IEEE1451 – template 33)
  • PSD the RS232 output option
Details
Universal Digital Signal Conditioner and Controller (UAB)
  • Wide range of Plug-In input modules providing transducer excitation
  • Fully flexible – any input module can be combined with any output module
  • Fully digital set-up and calibration using hand held plug-in display/keypad or comms
  • Optional local or remote LCD display and keypad
  • Simple one pass digital calibration for minimum set-up time on site
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • High accuracy and high stability over a wide temperature range
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • PCB (UAB) options include with case (D3) or without case (D2), DIN rail mounted
Details

Embedded & PCB Modules

Embedded Digital Load Cell Converter /Strain Gauge Digitizer Module (DCell)
  • Strain gage to RS485 or CAN digital load cell converter
  • Low profile, small 20mm diameter for mounting inside sensor
  • Ultra high performance, resolution of 1 part in 400,000 (18bit)
  • High speed, up to 500 Updates per second
  • Auto calibration or direct entry of mV/V with linearisation
  • Error reporting including strain gauge fault conditions
  • Programmable dynamic filter
  • Also available a miniature digital temperature sensor module for wiring to DCell/DSC temperature sensor pcb board
  • Option of an in-line enclosure
  • NEW! – ATEX component approval on CAN bus versions – Ex Na II
  • NEW! – Software enabling 24 DCell or DSCs to be viewed and logged simultaneously
Details
Evalution Kits for DCell & DSC (EVAL KIT)
  • Ideal way for first time users to familiarise with the Digitiser modules in test situations
  • RS232, RS485 & CANopen® Kits available
  • One ‘FREE’ DCell or DSC included in the cost of the kit – mounted and ready to go
  • Kit includes everything you need to communicate with the DCell or DSC card from you PC
  • Instrument Explorer software included for PC interface
  • A low cost way of discovering the benefits of the DCell/DSC
Details
Load Cell Amplifier and Digitiser PCB (LCB20)
Load Cell Amplifier and Digitiser PCB (LCB20)
  • PCB version
  • Simple auto calibration
  • 5V Excitation supporting up to 10 x Load Cells (350 R)
  • 0.5 to to 7.8 mV/V sensitivity
  • 6 wire input to compensate for barrier and cable losses
  • Full digital set-up and calibration using keypad or PC
  • Fully isolated analogue outputs 4-20mA & 0-10V
  • 10 pt linearization
  • Three x configurable digital inputs
  • Relay outputs:2 Setpoints SPCO
  • RS485 RS232 digital data output for communications and printing
  • Supports MODBUS RTU, ASCII & MANTRABUS
  • PCB (LCB20 shown in main photo) options include various cases with or without DIN rail mounting (shown in photos on left)
  • The LCB20 also has the option of a stainless steel case
Details
Digital Load Cell Converter (DSC)
  • Strain gauge to RS232, RS485 or CAN digital load cell conditioning card
  • OEM PCB format for easy fitting to products
  • Ultra high performance, resolution of 1 part in 400,000 (18bit)
  • High speed, up to 500 updates per second
  • Auto calibration or direct entry of mV/V with linearisation
  • Programmable dynamic filter
  • Temperature compensation
  • Error reporting including strain gauge fault conditions and overloads
  • Peak and trough (valley) recording
  • Remote shunt calibration by software command or digital input
  • Free software enabling 24 DSC or DCells to be viewed and logged simultaneously
    – see more here
  • DSC card option of enclosures for multiple x DSCs and a single DSC
Details
Strain Gauge to USB Convertor (DSCUSB)
Strain Gauge to USB Convertor (DSCUSB2)
  • High stability providing superior performance
  • USB strain gauge interface – device appears as a virtual com port
  • Simple & easy to connect to your strain gauge sensor
  • Multiple devices can be used with one PC
  • Free DSCUSB strain gauge to USB converter toolkit software
  • Compatible with most load cells and sensors
  • Non-expert maintenance
  • Windows driver DLL’s available
  • OEM pcb versions available
Details

Panel Mount

Panel Mount Weighing Indicator and Controller (ADW15)
  • Direct Strain Gauge input 4.5 digit resolution
  • Variable sensitivity from 0.5 to 200mV/V
  • Excitation 10V 160mA to drive up to 4 load cells
  • 6 wire input to compensate for zener barrier and cable losses
  • Simple one pass auto calibration for minimum set-up time on site
  • Auto tare and peak hold actioned by volt-free contacts
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • Programmable in-flight compensation for dynamic weighing operations
  • AC or DC power supply options
Details
Versatile Indicator, Controller, Analogue Conditioner (ADP15)
  • Large LCD display and keypad
  • Wide choice of input modules with transducer excitation
  • Fully isolated 4-20mA and 0-10V analog outputs
  • 2 Setpoints with relays outputs
  • Latching and inversion of relays
  • PID control, peak hold, display in engineering units
  • Fully digital set-up and calibration using keypad or comms
  • High accuracy and high stability
  • RS232 or RS485 data for setup, data transfer or label/ticket printing
  • Small panel space – DIN 72 x 72 mm – DIN rail mounting kit available
  • AC or DC power supply options
Details

Copyright © 2018 Sensors AS - All Rights Reserved
|HOME| |PRODUCTS| |HYDROPOWER| |NEWS| |CONTACT|
---
Sensors AS | Lørdagsrudv. 2 | 1472 Fjellhamar | Norway | Phone: +47 67 90 43 00 | Org. nr. NO 982 517 346 MVA

Sensors AS