Digital Indicators

Products > Instrumentation > Digital Indicators

Bulkhead

Display Module for DSC/DCell Digital Load Cells (RS485 input) (DS485DIS)
  • Displays for up to 8 DSC or DCell load cell aquisition devices
  • Provides summation of up to 8 load cell inputs
  • Gross/Net Toggle
  • Easy to operate toggle buttons
  • 6 Digit 20mm LED Display in Red
  • Removes the need for DSC/DCell to be permanently connected to a PC or PLC
Details
High Resolution Weighing Indicator and Controller (SMW-HR)
  • Resolution of 500,000 counts
  • Multi-point linearisation capability (4 points)
  • 12 Calibration profiles stores for 12 different sensors
  • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
  • Six wire measurement system can compensate for zener barrier losses
  • Fully digital set-up and calibration using built-in LCD display and keypad or comms
  • Auto tare and peak hold actioned by volt-free contacts
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • IP65 / NEMA4 ABS housing for bulkhead mounting
  • AC or DC power supply options
Details
Load Cell Amplifier and Digitiser Module (LCA20)
  • Full digital set–up using PC or keypad
  • 3 x configurable digital inputs e.g. for autotare, peak hold and reset
  • RS485 and RS232 digital data output for communications and printing
  • Measurement speeds 10 / 80 samples per sec
  • Factory calibration in mV/V
  • 5 V excitation supports up to 10 x 350 R load cells
  • Fully isolated 4-20 mA and 0-10 V analogue outputs
  • 6 wire input to compensate for barrier and cable losses
  • 2 set points SPCO relay outputs
  • Sensitivity from 0.5 to 7.8 mV/V
  • 10 pt linearization
  • Firmware now supports Mantrabus 1 & 2, MANTRA ASCII 2 & MODBUS RTU
  • ROHS Compliant & Environmentally sealed to IP65 / NEMA 4 enclosure dimensions 200 x 120 x 75 mm
  • Supplied in IP65 NEMA4 ABS protected case, stainless steel version or Din rail option see LCB
  • The LCA20 shown in main photo has the transparent lid option (LTL)
Details
Serial ASCII Display Module (SERIALDIS) wireless
  • 6 digit 7 segment LED 20mm display
  • Summation of 6 sensors
  • RS232 or RS485 serial ASCII input
  • Supports multidrop on RS485 (up to 15 sensors)
  • Waterproofed to IP65 NEMA 4
Details
Universal Digital Signal Conditioner and Controller (UAB)
  • Wide range of Plug-In input modules providing transducer excitation
  • Fully flexible – any input module can be combined with any output module
  • Fully digital set-up and calibration using hand held plug-in display/keypad or comms
  • Optional local or remote LCD display and keypad
  • Simple one pass digital calibration for minimum set-up time on site
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • High accuracy and high stability over a wide temperature range
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • PCB (UAB) options include with case (D3) or without case (D2), DIN rail mounted
Details
Versatile Indicator and Controller (SMP)
  • Large LCD display and keypad
  • Wide range of plug in input modules that provide transducer excitation
  • Fully isolated 4-20mA and 0-10V analog outputs
  • Setpoints and event handling using digital inputs and 2 x SPCO relays
  • PID control capability, peak hold, measurement in any engineering units
  • Fully digital set-up and calibration using built-in LCD display and keypad or comms
  • High accuracy and high stability over a wide temperature range
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • IP65 / NEMA4 ABS bulkhead mounting enclosure
  • AC or DC power supply options
Details
Weighing Indicator and Controller Bulkhead Mounted (SMW)
  • Large high resolution LCD display
  • 10V 160mA excitation for up to 6 Load Cells
  • Simple one pass auto calibration
  • 2 Set points, SPCO relay outputs
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications
  • IP65 / NEMA4 ABS housing for wall or surface mounting
Details

DIN Rail, Rack & Other

Load Cell Amplifier and Digitiser PCB (LCB20)
Load Cell Amplifier and Digitiser PCB (LCB20)
  • PCB version
  • Simple auto calibration
  • 5V Excitation supporting up to 10 x Load Cells (350 R)
  • 0.5 to to 7.8 mV/V sensitivity
  • 6 wire input to compensate for barrier and cable losses
  • Full digital set-up and calibration using keypad or PC
  • Fully isolated analogue outputs 4-20mA & 0-10V
  • 10 pt linearization
  • Three x configurable digital inputs
  • Relay outputs:2 Setpoints SPCO
  • RS485 RS232 digital data output for communications and printing
  • Supports MODBUS RTU, ASCII & MANTRABUS
  • PCB (LCB20 shown in main photo) options include various cases with or without DIN rail mounting (shown in photos on left)
  • The LCB20 also has the option of a stainless steel case
Details

Handheld

Portable Strain Gauge or Load Cell Indicator (PSD)
  • Portable handheld digital load cell indicator weighing only 250grams
  • Waterproof IP65 NEMA4 battery powered
  • 7 digit LCD display, with battery, peak, trough, net, overload and shunt cal indication
  • Battery life of 450 hrs in power save mode
  • Tactile keyboard, with on/off, range select, peak/valley hold, and gross/net controls
  • Microprocessor based, allowing single pass calibration facility (direct mV/V)
  • Dual range for values such as Kg and lb
  • TEDS enabled for automatic sensor calibration (IEEE1451 – template 33)
  • PSD the RS232 output option
Details

Panel Mount

Batch Weighing Controller, 12 Ingredients or Components (ADW-BW)
  • Up to 12 components or ingredients
  • Optional 10 menu selection
  • Selectable batch totals
  • Mixer timing control
  • Stand alone or PLC operation
  • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
  • Variable gain input sensitivity from 0.5 to 200 mV/V
  • 6 wire input to compensate for zener barrier and cable losses
  • Simple one pass auto calibration for minimum set-up time on site
Details
Panel Mount Weighing Indicator and Controller (ADW15)
  • Direct Strain Gauge input 4.5 digit resolution
  • Variable sensitivity from 0.5 to 200mV/V
  • Excitation 10V 160mA to drive up to 4 load cells
  • 6 wire input to compensate for zener barrier and cable losses
  • Simple one pass auto calibration for minimum set-up time on site
  • Auto tare and peak hold actioned by volt-free contacts
  • Fully isolated 4-20mA and 0-10V analog outputs
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
  • Programmable in-flight compensation for dynamic weighing operations
  • AC or DC power supply options
Details
Versatile Indicator, Controller, Analogue Conditioner (ADP15)
  • Large LCD display and keypad
  • Wide choice of input modules with transducer excitation
  • Fully isolated 4-20mA and 0-10V analog outputs
  • 2 Setpoints with relays outputs
  • Latching and inversion of relays
  • PID control, peak hold, display in engineering units
  • Fully digital set-up and calibration using keypad or comms
  • High accuracy and high stability
  • RS232 or RS485 data for setup, data transfer or label/ticket printing
  • Small panel space – DIN 72 x 72 mm – DIN rail mounting kit available
  • AC or DC power supply options
Details
Versatile Indicator/Controller with up to 16 Set Points (ADP-SP16)
  • Up to 16 set point relays (Rating 230V @ 5A AC)
  • All settings programmable from ADP15 keypad
  • Individual programmable setpoints & hysteresis values
  • Wide choice of input modules with transducer excitation
  • Industry Standard Analogue Outputs
  • Data Communications, Printer Driver
  • AC or DC power supply options
Details
Weighing Indicator Controller with up to 16 Set Points (ADW-SP16)
  • Up to 16 setpoints, each with an associated SPCO relay (on DIN rail module)
  • Individual set point, In-flight & hysterisis values
  • Programmable from the ADW keypad
  • Relay contact rating 230V @ 5A AC
  • Communications and Printer Driver
  • Simple one pass auto calibration for minimum set-up time on site
  • Provides excitation of 10V @ 160mA to drive up to 6 x 350 Ohm load cells
  • Variable gain input sensitivity from 0.5 to 200 mV/V
  • 6 wire input to compensate for zener barrier and cable losses
  • RS232 or RS485 communications for setup, data transfer or label/ticket printing
Details
Weighing Indicator/Controller for Fast Fill Operations (ADW-FFW)
  • For fast & accurate fill control
  • Fast 100 updates per second input
  • Fast & slow feeds
  • System speed optimisation
  • Auto tare
  • Auto calibration
  • Auto ‘In Flight ‘ compensation
  • ‘Weight complete’ output
  • Stand alone or control with PLC
Details
Weighing Indicator/Controller for Loss in Weight (ADW-LW)
  • For fast & accurate weight filling control
  • Tests for sufficient hopper contents prior to initiating the fill
  • Hopper replenishment and taring performed automatically
  • System speed optimisation (self-learning)
  • In Flight compensation
  • ‘Weight complete’ output and totaliser functionality
  • Stand alone system or additional control with PLC
Details

Copyright © 2018 Sensors AS - All Rights Reserved
|HOME| |PRODUCTS| |HYDROPOWER| |NEWS| |CONTACT|
---
Sensors AS | Lørdagsrudv. 2 | 1472 Fjellhamar | Norway | Phone: +47 67 90 43 00 | Org. nr. NO 982 517 346 MVA

Sensors AS